95 EPS courses

Duration 2 Days 12 CPD hours This course is intended for The primary audience for this course is any IT, facilities or data centre professional who works in and around the data centre and who has the responsibility to achieve and improve the availability and manageability of the data centre. Overview After completion of the course the participant will be able to:? Choose an optimum site for mission-critical data centre based on current and future needs? Describe all components that are important for high availability in a data centre and how to effectively setup the data centre? Name and apply the various industry standards? Describe the various technologies for UPS, fire suppression, cooling, monitoring systems, cabling standards, etc, and to select and apply them effectively to cost-efficiently enhance the high-availability of the data centre.? Review the electrical distribution system to avoid costly downtime? Enhance cooling capabilities and efficiency in the data centre by using existing and new techniques and technologies for the increased cooling requirements of the future? Design a highly reliable and scalable network architecture and learn how to ensure installers apply proper testing techniques? Create effective maintenance contracts with equipment suppliers ensuring the best return on investment? Setup effective data centre monitoring ensuring the right people get the right message? Ensure proper security measures, both procedural and technical, are established to safeguard your company's valuable information in the data centre The course will address how to setup and improve key aspects such as power, cooling, security, cabling, safety, etc., to ensure a high available data centre. It will also address key operations and maintenance aspects. THE DATA CENTRE, IT?S IMPORTANCE AND CAUSES FOR DOWNTIME DATA CENTRE STANDARDS AND BEST PRACTICES DATA CENTRE LOCATION, BUILDING AND CONSTRUCTION * Selecting appropriate sites and buildings and how to avoid pitfalls Various components of an effective data centre and supporting facilities setup RAISED FLOOR/SUSPENDED CEILING * Uniform, concentrated and rolling load definitions Applicable standards Raised Floor guidelines Signal Reference Grid, grounding of racks Disability act and regulations Suspended ceiling usage and requirements LIGHT * Standards Light fixture types and placement Emergency lighting, Emergency Power Supply (EPS) POWER INFRASTRUCTURE * Power infrastructure layout from generation to rack level ATS and STS systems Redundancy levels and techniques Three-phase and single-phase usage Power distribution options within the computer room Power cabling versus bus bar trunking Bonding versus grounding Common Mode Noise and isolation transformers Distribution boards, form factors and IP-protection grades Power quality guidelines Real power versus apparent power How to size and calculate load in the data centre Generators Static and dynamic UPS systems, selection criteria, how they operate and energy efficiency option Battery types, correct selection and testing Thermo-graphics ELECTRO MAGNETIC FIELDS * Electrical fields and magnetic fields definitions and units of measurements Sources of EMF Effects of EMF on human health and equipment (H)EMP Standards EMF shielding solutions EQUIPMENT RACKS * Rack standards, properties and selection criteria Security considerations Power rail/strip options COOLING INFRASTRUCTURE * Temperature and humidity recommendations Cooling measurement units and conversion rates Sensible and latent heat definitions Differences between comfort and precision cooling Overview of different air conditioner technologies Raised floor versus non-raised floor cooling Placement of air conditioner units and limitations to be observed Supplemental cooling options Cold aisle/hot aisle containment WATER SUPPLY * Importance of water supply and application areas Backup water supply techniques DESIGNING A SCALABLE NETWORK INFRASTRUCTURE * The importance of a Structured Cabling System Planning considerations Copper and Fiber cable technology and standards ANSI/TIA-942 Cabling hierarchy and recommendations Testing and verification SAN storage cabling Network redundancy Building-to-building connectivity Network monitoring system requirements FIRE SUPPRESSION * Standards for fire suppression Detection systems Various total flooding fire suppression techniques and systems, their benefits and disadvantages Handheld extinguishers Signage and safety Regulatory requirements and best practices DATA CENTRE MONITORING * Data centre monitoring requirements EMS versus BMS Water leak detection systems Notification options and considerations OPERATIONAL SECURITY AND SAFETY PRACTICES * Data centre security layers Physical, infrastructure and organisational security Safety measures and essential signage LABELLING * Choosing a labelling scheme Recommended labelling practices Network labelling DOCUMENTATION * How to setup proper documentation Document management policies and procedures CLEANING * Cleaning practices for the data centre MTBF/MTTR * Standards and definitions Calculation models The ?real? value MAINTENANCE CONTRACTS/SLA/OLA EXAM: CERTIFIED DATA CENTRE PROFESSIONAL ADDITIONAL COURSE DETAILS: Nexus Humans Certified Data Centre Professional (CDCP) training program is a workshop that presents an invigorating mix of sessions, lessons, and masterclasses meticulously crafted to propel your learning expedition forward. This immersive bootcamp-style experience boasts interactive lectures, hands-on labs, and collaborative hackathons, all strategically designed to fortify fundamental concepts. Guided by seasoned coaches, each session offers priceless insights and practical skills crucial for honing your expertise. Whether you're stepping into the realm of professional skills or a seasoned professional, this comprehensive course ensures you're equipped with the knowledge and prowess necessary for success. While we feel this is the best course for the Certified Data Centre Professional (CDCP) course and one of our Top 10 we encourage you to read the course outline to make sure it is the right content for you. Additionally, private sessions, closed classes or dedicated events are available both live online and at our training centres in Dublin and London, as well as at your offices anywhere in the UK, Ireland or across EMEA.

VOICE OVER LTE TRAINING COURSE DESCRIPTION This course provides a basic understanding of the 3G LTE Air Interface, SAE, as well as Voice over LTE options and LTE Advanced features. Investigating the standards for the EPS , formulated by the 3GPP standards body, the course will set out to examine and explain the 4G environment from user equipment to border gateway and beyond. This course will ensure the delegate has a grasp of all aspects of the current global deployments, the next steps in upgrades and the promise of things to come. WHAT WILL YOU LEARN * Describe the complete EPC architecture. * Explain the use of QoS within the air interface & core network. * Explore the features of LTE advanced. * Describe the various methods of supporting voice services with 3G LTE. * Describe IMS structure and control entities. * Explain an IMS session. VOICE OVER LTE TRAINING COURSE DETAILS * Who will benefit: Any engineers who are assisting in the deployment of voice services within their LTE networks. * Prerequisites: Intro to Data comms & networking Telecommunications Introduction * Duration 3 days VOICE OVER LTE TRAINING COURSE CONTENTS * 3GPP standards body Release 8 - Release 12, Supported and expected features. * The EPC revisited EPC revisited 3G LTE & EPC Architecture, NB, MME, SGW, PDNGW, PCRF, Interworking capabilities, Protocol stack explored, NAS signalling, Default EPS bearer, Slot allocation algorithms, Scheduling algorithms, Quality of Service requirements, Dedicated EPS bearers. * VoLTE deployment strategies Common networks everywhere, GSM/WCDMA view, CDMA view. * VoLTE system architecture LTE radio, LTE Radio background, LTE radio architecture, Evolved packet core, EPC entities & functions, EPS mobility management, MS entities, Home subscriber server, Policy & charging rules function. * VoLTE functionality Radio functionality, Bearers & schedulers, Mobility, Circuit switched fall back handover, Mobility from 2G/3G back to LTE, Power Saving Features, Positioning services, UE radio access capabilities for VoLTE users. EPC functionalities, LTE subscriber identification, PDN connectivity establishment, EPS dedicated bearer setup, IMS identification, IP multimedia identification module, Public user identity, Private user identity, Relationship between public & private identity, identification of users device, identification of network entities, identification of services, identification without ISIM. IMS service provisioning, Enforcement of allowed services, Service triggering information, Selection of the AS, AS behaviour, Service provisioning in action. * VoLTE end-to-end & signalling VoLTE subscription & device configuration. EPS attach for CSFB/IMS VoIP & default bearer. IMS registration, Constructing the REGISTER request, From UE to P-CSCF, From P-CSCF to I-CSCF, From I-CSCF to S-CSCF, S-CSCF challenges the UE, UE's response to the challenge, Registration at the S-CSCF, The 200 OK response, Third-party registration to application servers, Subscription to registration event package, Re-registration & re-authentication, De-registration, Related standards. IMS VoIP session, Constructing the INVITE request, Routing, Media negotiation, Media resource reservation & policy control, Charging, Session release. Voice continuity, PS - PS intersystem handover, Single radio voice call continuity. IMS emergency session, PDN Connection setup for emergency session, Emergency registration, Emergency session. CS fallback for EPS call case, Architecture of CS fallback in EPS, Description of SGs interface, Idle mode signalling reduction, Idle mode vs active mode, CS fallback attachment, Mobile originating call using CSFB, Mobile terminating call using CSFB, Call unrelated CSFB procedures, Mobile terminating roaming retry & forwarding. VoLTE Messaging, Native IMS messages, SMS interworking, Multimedia messaging service. Unstructured supplementary services data simulation in IMS. * IMS services VoLTE radio performance Coverage, Latency, Capacity. * LTE advanced features Carrier aggregation, Coordinated mMulti-point Operation (CoMP), ICIC & eICIC, Relay node deployment & donor eNBs, Improved cell edge coverage, Reduced control plane latency, Heterogeneous networks, HeNB, security gateways, HeNB gateways.

LTE OPTIMIZATION TRAINING COURSE DESCRIPTION This course gives delegates an understanding of the Key Performance Indicators used within the 3G LTE (4G) network environment. We investigate the 3GPP standards for KPIs (including TR 32.814, TS 32.410 & TS 32.455) these cover GERAN, UMTS & LTE environments. The course details the optimisation procedures and the use of Self optimisation, Selforganising & Self-healing equipment now being deployed across all releases of mobile networks. WHAT WILL YOU LEARN * Explain the RF optimisation flowchart. * Describe the importance of Reference Signal Received Power (RSRP). * List many of the 3GPP recommended KPIs. * Describe the concept of APN AMBR and UE AMBR within LTE. * Describe the use of planning and optimisation computer tools. LTE OPTIMIZATION TRAINING COURSE DETAILS * Who will benefit: Anyone working with LTE. * Prerequisites: Essential LTE * Duration 2 days LTE OPTIMIZATION TRAINING COURSE CONTENTS * Introduction to the cellular environment The architecture, 2G (GSM), GPRS/EDGE, The NGMN (Next Generation Mobile Network), media gateway controller, 3GPP Rel99 the 3G introduction, HSPA deployments, 3G LTE (4G). * Cellular network procedures GSM/GPRS call setup, GPRS data call setup, 3G UMTS data call setup, Data call (Voice over LTE) in LTE (using IMS), Circuit Switched Fall Back (CSFB) in LTE, IP packet session in LTE. * Introduction to the standards The 3GPP specifications body, The numbering structure for KPIs, 2G KPIs, 3G/UMTS KPIs, 3G LTE KPIs, IMS KPIs. * Introduction to the KPI definitions KPI definitions, accessibility KPIs, retainability KPIs, mobility KPIs, utilisation KPIs. * In-depth overview of the air Interfaces GSM/GPRS FDMA & TDMA solution, 3G UMTS WCDMA solution, HSPA+ sharing spare power (Codes), The 3G LTE uplink & downlink interface explained, Initial attach procedures explained. * Problem analysis Reference Signal Received Power (RSRP), Signal to Interference Noise Ratio (SINR), handover success rates, power adjustments, classification of coverage problems, weak coverage & coverage holes, lack of dominant cells, cross coverage, improper tilt settings, uplink/downlink imbalance, signal quality, Azimuths & tilts to reduce interference, Handover failure due to interference, Service drop causes. * Mobile RF performance in 2G/3G Performance counters, KPIs, testing & measurement, Drive testing and survey, Data collection and post processing of data, LTE service optimization, bandwidth, poor coverage, Quality, optimization process, KPI optimization, Root Cause Analysis (RCA) applied to RF issues, optimization tools and software. * Advanced LTE network planning & optimization LTE UE measurements (RSRP/RSRQ), LTE capacity planning, RF configuration parameters, LTE cell selection/reselection planning, LTE radio network KPIs, LTE user-centric KPIs, LTE network performance KPIs, LTE system utilization KPIs, LTE RF channel performance predictions, LTE channel information processing, LTE channel multiplexing, Physical layer and structure, MIMO in LTE, LTE resource plan LTE and Self-Organizing Networks (SON). * Radio network optimization work flow Work flow, the existing network, Optimization team establishment and cluster division, Single site verification, Alarm check, Cell state check, Radio parameters check, Site verification, Statistics analysis, Coverage problem analysis. * Mobile internet and QoS issues Cellular QoS reference models. How QoS impact on KPIs and measurements, Introduction to mobile internet, The concept of shared access technologies, Support for QoS in the WCDMA environment, The PDP context model, Supporting end-to-end QoS, EPS bearer concepts, Default EPS bearer, Dedicated EPS bearer, APN-AMBR, UE-AMBR.

LTE ARCHITECTURE AND PROTOCOLS COURSE DESCRIPTION This course provides a comprehensive tour of the LTE architecture along with services provided and the protocols used. WHAT WILL YOU LEARN * Describe the overall architecture of LTE. * Explain the information flows through LTE. * Describe the LTE security. * Describe LTE mobility management. * Recognise the next steps for LTE. LTE ARCHITECTURE AND PROTOCOLS COURSE DETAILS * Who will benefit: Anyone working with LTE. * Prerequisites: Mobile communications demystified * Duration 3 days LTE ARCHITECTURE AND PROTOCOLS COURSE CONTENTS * Introduction History, LTE key features. The 4G ITU process. The LTE 3GPP specifications. Specifications. * System Architecture LTE hardware architecture. UE architecture and capabilities. E-UTRAN and eNB. EPC, MME functions, SGW, PGW and PCRF. System interfaces and protocol stacks. Example information flows. Dedicated and default bearers. EMM, ECM, RRC state diagrams. * Radio transmission and reception OFDMA, SC-FDMA, MIMO antennas. Air interface protocol stack. Logical, transport and physical channels. Frame and slot structure, the resource grid. Resource element mapping of the physical channels and signals. Cell acquisition, data transmission and random access. MAC, RLC, PDCP protocols. LTE spectrum allocation. * Power-on procedures Network and cell selection. RRC connection establishment. Attach procedure, including IP address allocation and default bearer activation. LTE detach procedure. * Security in LTE networks LTE security features, identity confidentiality, ciphering and integrity protection. Architecture of network access security in LTE. Secure key hierarchy. Authentication and key agreement procedure. Security mode command procedure. Network domain security architecture. Security associations using IKE and IPSec. * Mobility management RRC_IDLE, RRC_CONNECTED. Cell reselection, tracking area updates. Measurement reporting. X2 and S1 based handovers. Interoperation with UMTS, GSM and non-3GPP technologies such as cdma2000. * QoS, policy control and charging QoS in LTE, EPS bearers, service data flows and packet flows. The architecture and signalling procedures for policy and charging control. Data transport using GPRS, differentiated services and MPLS. Offline and online charging in LTE. * Delivery of voice and text messages over LTE Difficulties and solutions for Voice over LTE. Architecture and call setup procedures for circuit switched fallback. Architecture, protocols and call setup procedures in IP multimedia subsystem. * Enhancements in release 9 LTE location services. Multimedia broadcast / multicast service and MBSFN. Cell selection, commercial mobile alert service. * LTE Advanced and release 10 Impact of carrier aggregation on LTE air interface. Enhanced MIMO processing on uplink and downlink. Relaying. Release 11 and beyond. * OAM and self organising networks Operation, administration, maintenance and provisioning for LTE. Self-configuration of base station parameters. Fractional frequency re-use, inter-cell interference co-ordination. Self-optimisation of base station procedures. Self-healing to detect and recover from faults.

The Greek Language Summer Camp is a great way for your child to greatly improve their Greek and have fun with other international children. Our program is for children aged 6-15 years and aims to develop children’s speaking skills and boost their confidence when speaking Greek. Young learners are usually faster to learn and grasp foreign languages, especially some aspects of languages like the pronunciation and new vocabulary. This is precisely why close contact with a Greek speaking environment and native Greek speakers is the perfect opportunity for children to engage in the Greek language fast and absorb new skills very quickly.

OVERVIEW Take the most significant steps to turn your enthusiasm for working in the pharmaceutical industry into a reality. Through this Pharmacy Assistant Foundation Training course, you will get a glimpse of what it takes to work as a pharmacy assistant.  Our in-depth Pharmacy Assistant Foundation Training will thoroughly introduce you to the role and responsibilities of a Pharmacy Assistant. It will educate you on the patient counselling guidelines and communication techniques for optimal therapeutic outcomes. In addition, you will learn about the dispensing medication procedure, dispensing errors prevention methods and EPS.  The training will also help you acquire the necessary skills in inventory control and management processes and Standard Operating Procedures (SOPs). By the end of the course, you will have a clear concept of performing all clerical activities required for the smooth and efficient running of a Pharmacy.   LEARNING OUTCOMES * Familiarise yourself with the duties of a pharmacy assistant * Understand the steps involved in patient counselling * Learn how to communicate in pharmacy settings * Acquire knowledge about prescription and dispensing in pharmacy settings * Learn about  the dispensing methods, EPS, minimising dispensing errors in pharmacies * Understand the process of inventory control and management in pharmacies * Familiarise yourself with the Standard Operating Procedures (SOPs) * Learn about health and safety risk assessment and pharmaceutical terminology WHO IS THIS COURSE FOR? Anyone interested in learning the essential skills required to be a pharmacy assistant or technician can take this Pharmacy Assistant Foundation Training Course. Those who are already in the pharmacy profession will also benefit from this training.  Gaining the knowledge and skills will provide the first and most significant steps for starting a career in the Pharmaceutical industry!  ENTRY REQUIREMENT * This course is available to all learners of all academic backgrounds. * Learners should be aged 16 or over. * Good understanding of English language, numeracy and ICT skills are required to take this course. CERTIFICATION * After you have successfully completed the course, you will obtain an Accredited Certificate of Achievement. And, you will also receive a Course Completion Certificate following the course completion without sitting for the test. Certificates can be obtained either in hardcopy for £39 or in PDF format at the cost of £24. * The PDF certificate's turnaround time is 24 hours, and for the hardcopy certificate, it is 3-9 working days. WHY CHOOSE US? * Affordable, engaging & high-quality e-learning study materials; * Tutorial videos and materials from the industry-leading experts; * Study in a user-friendly, advanced online learning platform; * Efficient exam systems for the assessment and instant result; * United Kingdom & internationally recognised accredited qualification; * Access to course content on a mobile, tablet, and desktop from anywhere, anytime; * Substantial career advancement opportunities; * 24/7 student support via email. CAREER PATH The Pharmacy Assistant Foundation Training course provides essential skills that will make you more effective in your role. It would be beneficial for any related profession in the industry, such as: * Pharmacy Assistant * Relief Pharmacy Assistant * Pharmacy Dispenser Pharmacy Assistant Foundation Training Module 1: Introduction to Pharmacy Assistant and Pharmacy Technician 00:16:00 Module 2: Job Role of Pharmacy Technicians 00:25:00 Module 3: Pharmacy Assistant Patient Counselling Guide 00:20:00 Module 4: Communication in Pharmacy Settings 00:16:00 Module 5: The Pharmacy Team and Practices 00:17:00 Module 6: Prescription and Dispensing in Pharmacies 00:20:00 Module 7: Dispensing Methods, EPS, Minimising Dispensing Errors in Pharmacies 00:17:00 Module 8: Inventory Control and Management in Pharmacies 00:20:00 Module 9: Standard Operating Procedures (SOPs) 00:13:00 Module 10: Health and Safety Risks Assessment and Pharmaceutical Terminology 00:21:00 Order Your Certificates and Transcripts Order Your Certificates and Transcripts 00:00:00

Introduction to Hand Building and Sculpture and opportunity for others to increase skill -------------------------------------------------------------------------------- SERVICE DESCRIPTION 8 week, 2.5 hour sculpture course. Get your creativity back! Hand Building and sculpture class for students with little to no experience and those with some experience in clay sculpture. You will learn the basics of Hand Building and sculpture in clay; how to create mugs, vases and sculptures from pinch pots, slabs and solid blocks of clay. In this course we will be working to create torso vases/wooden spoon holders, tea light cottages as well as sculpted plant pots etc. I love to work with different colour media and surface design. I encourage my students to do the same and have equipped The EPS with underglazes, slips, oxides and glazes to allow for a wide range of choices for decorating your work. I have been throwing and hand building for 20 years and learned many skills along the way that I will share with you to ensure that you succeed in this class and leave with pieces that you are proud of. COURSE PACKAGE: * 2.5 Hour Hand Building and Sculpture class * Demonstrations and instruction from an established ceramic artist * Access to expert advice via Wix or Facebook * Slips, glazes and stoneware firing included * Space in the studio to leave your clay for the next week * Opportunity to join The EPS Hands on Clay, pottery user's group (HUG) after 4, 10 week courses taken in the studio IN THE INTEREST OF COVID SAFETY AND CLEANLINESS, PLEASE BRING An apron, small towel and pillow sized cloth, large sponge, and a 2 litre tub Clay is to be purchased separately on this website before class begins * 1/2 bag of clay for 5 weeks - £7 - £10 * Full bag for 8 weeks - £14 - £20 Purchase Crank or Raku for sculpture that does not need to hold water and anything else for mugs, cups etc that need to hold water I am really looking forward to teaching and making ceramics with you and would love you to see you in this new, pottery studio. * So long as you withdraw two weeks before teaching begins, refunds accepted, minus 5% transaction fee. After this period, all tuition fees are non-refundableRefunds are not available once a period of study has commenced.* -------------------------------------------------------------------------------- Cancellation Policy To cancel or reschedule a class or course, please phone or text a week in advance t o give me a chance to fill your space and offer it to lower income students. Please note that refunds are only given 14 days prior to the start of your course. See course details for further information by

All person centred planning tools and processes are driven by a commitment to achieve inclusive outcomes for the person whose plan it is, and the young people involved are always present throughout their planning session. The focus of all person centred approaches is the whole person irrespective of the label they carry. Two people, a process facilitator and a graphic facilitator, typically facilitate plans. COURSE CATEGORY Person Centred Planning Inclusion Strategic Work Visioning and Problem Solving DESCRIPTION Person centred planning is a way of expressing a set of inclusive values through a unique range of tools and techniques. The most commonly used person centred tools – MAPS [https://inclusive-solutions.com/product/maps-process-step-by-step-guide/] and PATH [https://inclusive-solutions.com/product/path-process-step-by-step-guide/] – create a hands-on demonstration of these values in action. All person centred planning tools and processes are driven by a commitment to achieve inclusive outcomes for the person whose plan it is, and the young people involved are always present throughout their planning session. The focus of all person centred approaches is the whole person irrespective of the label they carry. Two people, a process facilitator and a graphic facilitator, typically facilitate plans. The role of the support service staff in this work is as a facilitator not as an expert participant, problem solver, assessor or provider of consultation. MAPS [https://inclusive-solutions.com/product/maps-process-step-by-step-guide/] and PATH [https://inclusive-solutions.com/product/path-process-step-by-step-guide/] are especially effective tools in planning transitions and annual review processes for young people with additional support needs and for through-care planning for young people who are looked after or accommodated. Over time person centred working will reveal areas of unmet need in current provision and thereby inform the ongoing strategic planning within any particular region. TESTIMONIALS > “Thanks again for a superb day which from my perspective as Principal > Educational Psychologist has been a real boost and uplifted my spirits about > helping move the Educational Psychology Service forward as well as gaining > greater insight and understanding of individual Educational Psychologists. > Several EPs have said that they are planning to use MAPS > [https://inclusive-solutions.com/product/maps-process-step-by-step-guide/] and PATHS > [https://inclusive-solutions.com/product/path-process-step-by-step-guide/] in > their work and I will be joining them.” > > DR MICHAEL HYMANS, PRINCIPAL EDUCATIONAL PSYCHOLOGIST, LONDON BOROUGH OF LEARNING OBJECTIVES 1. To Explore the values underpinning person centred working 2. To show how person centred planning naturally captures young people’s strengths and capacities 3. A demonstration of how person centred planning encourages meaningful consultation and participation with young people (particularly for those who cannot make their views known in typical ways 4. To show how Person Centred Planning leads to the building of stronger parent/school partnerships 5. To indicate how person centred planning can promote multi-agency teamwork and shared responsibilities 6. To increase understanding the how of process and graphic facilitation in person centred work. WHO IS IT FOR ? * Teachers and School Staff * Education Services * Social Care Staff * Health Professionals * Transition Coordinators * Family Support Workers * Link Workers COURSE CONTENT * An introduction to the person centred planning tools * PATH [https://inclusive-solutions.com/product/path-process-step-by-step-guide/] live demonstration in action followed by real time coaching of facilitation skills. We would stress that this is an introductory day and that participants will be expected to make plans for their own follow up and further practice of the tools covered in the course of the day.

Pharmacy Assistant and Technician is yet another 'Teacher's Choice' course from Teachers Training for a complete understanding of the fundamental topics. You are also entitled to exclusive tutor support and a professional CPD-accredited certificate in addition to the special discounted price for a limited time. Just like all our courses, this Pharmacy Assistant and Technician and its curriculum have also been designed by expert teachers so that teachers of tomorrow can learn from the best and equip themselves with all the necessary skills. Consisting of several modules, the course teaches you everything you need to succeed in this profession. The course can be studied part-time. You can become accredited within 08 days studying at your own pace. Your qualification will be recognised and can be checked for validity on our dedicated website. WHY CHOOSE TEACHERS TRAINING Some of our website features are: * This is a dedicated website for teaching * 24/7 tutor support * Interactive Content * Affordable price * Courses accredited by the UK's top awarding bodies * 100% online * Flexible deadline ENTRY REQUIREMENTS No formal entry requirements. You need to have: * Passion for learning * A good understanding of the English language * Be motivated and hard-working * Over the age of 16. CERTIFICATION CPD Certification from The Teachers Training Successfully completing the MCQ exam of this course qualifies you for a CPD-accredited certificate from The Teachers Training. You will be eligible for both PDF copy and hard copy of the certificate to showcase your achievement however you wish. * You can get your digital certificate (PDF) for £4.99 only * Hard copy certificates are also available, and you can get one for only £10.99 * You can get both PDF and Hard copy certificates for just £12.99! The certificate will add significant weight to your CV and will give you a competitive advantage when applying for jobs. Module 1: Introduction to Pharmacy Assistant and Pharmacy Technician Introduction to Pharmacy Assistant and Pharmacy Technician 00:16:00 Module 2: Job Role of Pharmacy Technicians Job Role of Pharmacy Technicians 00:25:00 Module 3: Pharmacy Assistant Patient Counselling Guide Pharmacy Assistant Patient Counselling Guide 00:20:00 Module 4: Communication in Pharmacy Settings Communication in Pharmacy Settings 00:16:00 Module 5: The Pharmacy Team and Practices The Pharmacy Team and Practices 00:17:00 Module 6: Prescription and Dispensing in Pharmacies Prescription and Dispensing in Pharmacies 00:20:00 Module 7: Dispensing Methods, EPS, Minimising Dispensing Errors in Pharmacies Dispensing Methods, EPS, Minimising Dispensing Errors in Pharmacies 00:17:00 Module 8: Inventory Control and Management in Pharmacies Inventory Control and Management in Pharmacies 00:20:00 Module 9: Standard Operating Procedures (SOPs) Standard Operating Procedures (SOPs) 00:13:00 Module 10: Health and Safety Risks Assessment and Pharmaceutical Terminology Health and Safety Risks Assessment and Pharmaceutical Terminology 00:21:00 Recommended Readings Recommended Readings : Pharmacy Assistant and Technician 1 week, 1 day

2 QLS Endorsed Course | CPD Certified | Free PDF + Hardcopy Certificates | 80 CPD Points | Lifetime Access